Recycle, Reuse, Reflect

A while back I picked up a beat up old tool box at a garage sale.  The proprietor had a price of ten bucks on the box with all the contents.  The box didn't have much in it so I mostly bought it to examine the construction.  Here is the tool box:

Red Tool Box

I don't usually post such large photos, but wanted to show the construction details of the tool box.  The corner joints are all finish nailed with no glue.  A simple leather strap held on with roofing nails serves as a handle on each side.

The guy selling it told me his grandfather made this toolbox and used it.  He did not know what trade he was in.  The contents consisted of some large cold chisels, a homemade dowel plate and two beat up saws.  Here are the contents of the box sans hand saws:

Notice that the remaining paint on the tools exactly matches the toolbox.  There is no other personalization on the tools or box so my assumption is that the original owner/builder used the red paint to mark the stuff as his.  By all means offer any alternative theories below.

Here is one of the saws:

The saws were well used and kinked in multiple places.  They aren't even worth practice sharpening.  Also, note again the red paint on the handle.

The best 'find' in this tool box is the dowel plate.  One of the holes is even threaded for whatever purpose; I'll use it to thread dowels if need be.  The other tools I tossed into my large Craftsman chest dubbed the Island of Misfit Tools.

After examining the toolbox, I was about to chuck it after the saws into the garbage heap.  For some reason I hesitated and kept the empty box around.  I don't know who built the toolbox.  I have no connection whatsoever with it's history, but it occurred to me that I could be part of it's future.  My oldest son found the perfect use for this old toolbox:

All of my small sanders fit perfectly in the box.  Now the big red toolbox is going to be home to all of my small sanders.  The previous owner could care less, the builder may or may not be pleased that this box survived the years to arrive in my care.  All I know is that now whenever I need a sander, it should be in the obnoxious red box on the back shelf of the garage shop.

Civil War Folding Table: Finished Is Finished

I know the blog has been neglected for several months, but I have not been idle in the shop.  I have a good excuse, I think.  Highland Woodworking is interested in my writing from an amateur's view.  My writing time has been spent on more in depth stuff for them; they may or may not accept the work for publication.  Either way there is more content for the blog, eventually.

Today we are going back to the Civil War folding table from Woodworker's Journal.  The last entry on the Civil War table is here.  The table build was unintentionally stretched out in the following blog posts:

     That'll Do, Pig. That'll Do
     Discretion Is The Better Part Of Valor
     A Peek Into The Sausage Factory

Here are before and after pictures of the finish:

 The finish is 3 applications of Danish Oil in Natural color.  The oil was left to cure for about 40 days.  After aging, I lightly sanded with 400 grit paper and a brown paper bag.  On top of the oil is bleached dewaxed shellac.  The top has four coats and the rest of the table has three coats of shellac.  The table was rubbed with a brown paper bag between coats, except for a very light hand with the 400 grit paper after the first coat of shellac.  The final touch is two coats of Johnson Paste Wax applied to the top.

Here are the rest of the pictures from final photo shoot.

I think I have enough material to make another similar table.  The decision as to folding legs is still up in the air.  If you peruse the previous blog posts, you'll find I have a set of legs that were 'ruined' by a silly design decision that I made; the goal is to use these expensive experiments elsewhere.

I encourage any woodworker to tackle this project.  It is actually quite an easy thing to build with both power and hand tools.  You might want to look for a lighter wood.  This table was built with White Oak and Padauk and consequently is very heavy.  The mass is good for me as I don't intend to sling this around like a big box store 20 dollar card table.

2013 Dutch Tool Chest Completed

Completed, but with an asterisk.  The hinges for the top are still on back order.  A till for two joinery saws will be installed on the lid after the hinges are installed.  I also plan to mimic Chris Schwarz's block plane holster found in his published Dutch tool chest.

Empty Carcase

This post is meant to be a 'How I Did It' commentary.  As usual, I don't profess to be an authority on woodworking in general, and Dutch tool chests in particular.  To the left is the completed carcase built to the large chest plan found in Popular Woodworking, October 2013.

I did the glue up of the carcase alone.  I used run of the mill Titebond wood glue to join the dovetails at the bottom of the chest.  I had some difficulty getting the shelves into their dadoes and the glue was pretty well set up by the time the clamps were on.  The carcase was out of square so I forced it square and nailed a cross brace across the back.  The shelves are only nailed in from the outside with no glue.

The carcase settled in slightly out of square (about a quarter inch) when the clamps and cross brace came off.  I did what I could to force it back to square when I screwed on the front plate.  The back consists of inexpensive home center carsiding because it is already tongued and grooved.  I screwed and nailed on the carsiding level with the bottom of the chest.  I left the sides protruding beyond the chest on both sides to account for being out of square.  I then planed the end grain level with the chest side.  I never planed nearly three feet of end grain before and found that it was not as easy as I'd hoped, but not as hard as I'd feared.

Full Chest

Above is the full chest.  The top is organized, but I just threw a bunch of stuff into the bottom to clear some space on the table.  The personalization of this project is all on the inside, and then mostly in the top.  Here is the top full of tools:

Organized Top Of Chest

A previous post stated that there would be two rows of tools in the tool rack.  However, the plan changed when I finally started playing jigsaw puzzle with the planes.  The space was designed from the bottom up.  And I still ended up with a second tool rack.  There are 12 tools in the rack at the top right of the photo; here is a close up:

Secondary Tool Rack

However, I'm getting ahead of myself.  The space was designed from the bottom.  Painstaking tolerances were achieved for the planes by using circular calibration disks, washers for short.

Bare Bottom

Almost Done

The strips of wood are all from the scrap pile.  The left and right have a rounded over strip that the planes rest on to keep the blade off the bottom of the chest.  David Charlesworth is always placing his planes similarly in his videos, thus I'm simply emulating a Master.  

I often hear the reasoning for a plane kickstand is to keep the blade from getting dull; I believe the real reason is to isolate the cutting edge from a moisture retaining material (wood) to prevent rust.   

Getting back on track.  The wood strips are held down simply with glue.  I used screws and weight to hold them down while the glue was setting.  In the photo above the screws are coming out after the glue is set.  The screws came out to minimize metal to metal contact.  I ascribe to the philosophy that tools should always touch material softer than they are as much as possible; also, I hate sharpening.

Here is a close up photo that was just too cool not to post:

Close Up Of Tool Separators

The tool organization is designed to merely prevent contact with surrounding tools during ingress and egress (put'em n take'em).  This Dutch tool chest will not be traveling further than the basement shop and is not designed to protect during transport.

Here is a picture of my Lee Valley brass mallets in action:

Mallet Clamp (TM, Copyright, R, by me)

Gravity At Work

 The photo with block plane is a till for my dovetail saw.  It was fairly simple to make.  The kerf was started in a miter box and then finished with the saw itself:

Miter Box To Start Till Kerf

Saw To Finish Saw Kerf

I made two custom brackets for the tool rack.  The first holds a small square, the second a marking knife.  They both started from a block of wood (doesn't all our stuff?) before joining the tool chest.

Raw Knife Holder

I like this shot of the mounted knife holder.  I have a crappy camera, and worse skill when it comes to photography, so my standards are pretty low.

I will be building a second chest and a saw buck to complete my basement shop storage.  My idea of a saw buck comes from Ron Herman of Antiquity Builders.  It is a wood box that holds a complete set of handsaws.  Unfortunately, I neither have, nor wrote down what Ron deems a complete set of hand saws.  My box will be a simple rectangle about 28-30 inches tall, 10 or 11 inches wide and 7-8 inches deep with enough slots to hold 7 or so saws.  Apologies in advance for half-assing Ron's design.

Here are a couple more pictures that I took of the chest.

Tool Rack Looking Left

Tool Rack Looking Right

Look at the individual tool holders on the sloped left and right panel in the above two pictures.  I thought about custom making the sloped holders.  However, it seemed to me to be a lot of work with very little return.  These clips are often part of pre-mounted sets of tool organizers that you find in hardware stores and home centers, but you never see them offered alone (I don't, at least).  Certainly they would never be found at the exact slope you would need for any particular project.  I don't know the industry term for them beyond "spring clip" so there wasn't much success to be had on the friendly neighborhood Internet search engine.  I contacted a manufacturer, Gibson Good Tools, for retail sources of their product.  A very prompt reply from a nice sales person named Leigh offered to ship direct product in lots of 100 or more, and some retail sources.  I do plan to take them up on their offer of mass quantities if and when I start reorganizing the garage workshop.  In the meantime, I'll go with retail since I'm not building two dozen Dutch tool chests.

I don't know why I didn't think of this to start, but I found (because Leigh told me I would) the needed clips in the proper quantities at McMaster-Carr.  I don't know if you are acquainted with McMaster-Carr, but they are the type of operation that if a company starts making Splendiferous Widgets at 8am and you call McMaster at noon to buy them, by 3pm they will have photographs, SKU information, and a shipper tracking number for you.  Here are the clips I purchased:

1 1723A21 Tool Holder, Zinc-Plated Steel, for 3/8" - 5/8" Tool Diameter, Packs of 10
2 1722A41 Tool Holder, Nickel-Plated Steel, for 3/16" - 3/8" Tool Diameter, Packs of 10
3 1722A42 Tool Holder, Nickel-Plated Steel, for 5/16" - 3/4" Tool Diameter, Packs of 10

Only one of the smallest clips were used in the tool chest (line item 1).

Again referring to the two photos above.  On the left you see my three custom Grace screwdrivers and an inexpensive countersink driver that the origin of which I don't remember.  The right side features most of my set of Grace woodworking screwdrivers.  I fit seven of the 8 Grace woodworking drivers in the tool chest.  The tallest, for #14 screws, would not fit by just a smidgen.  I could modify the wood handle to make it fit, but I really like the way Grace drivers feel in my palm and don't want to risk losing that feel.

The spacing for the clips is all by eye.  I mounted examples of each purchased clip on a piece of scrap.  From there I tested which clip fit which tool the best.  The last step was to fill the chest up and eyeball what fit where on the sides and screw in the clip.

The last post on the construction of this chest will come when I finally get the hardware for the top.  I'll probably have the second one built before that happens!

Disposed Income

Well, this is my end of year blog entry where I talk about my annual woodworking shopping habits.  The woodworking purchases have been pretty low this year as evidenced in the blog entry calendar to the right of the page.  Here is the short list for 2013:

Lie-Nielsen I finally completed my chisel set and added some floats to my arsenal.
Highland Woodworking  I visit their site every other week at least.
McFeely's  It feels like I've purchased thousands of screws from them this year.
Tyler Tool  A new entrant to the list this year.  A great no frills source for power tools.
Lost Art Press  Most the stuff I buy from them is reviewed on the blog, so I'm not adding details here.
CU woodshop  This is an independent outfit in Champaign IL.  They have a great selection in stock from power tools to milk paint and, of course, wood.
Owl Hardwood lumber  There is a Hooter's one block away.  It is always a three or four hour outing when I go to Owl. Not including travel.
Woodcraft  Most of my odds and ends are filled by this place, it seems.
Menard's and Lowes  Interchangeable on most things so they get one line.
Amazon  The 7-eleven of the ether, and soon landing smiley boxed Stuff in your own backyard.

I'm giving a shout out to the many anonymous yard sales and flea markets I frequent.  I scored some major wood and paring chisels over the summer.

I'll return and add anyone I've forgotten.  Best wishes to you and yours in the coming year.

Court Jester Woodworker?

Sometimes I wonder why I keep at this woodworking thing.  Sure, I have a couple cool tables and a score of scout derby cars for my efforts.  But, it seems the more I do it, the more my shortcomings are revealed.

I finished the carcase for the Dutch tool chest a la Popular Woodworking and Chris Schwarz.  The top hinges are on back order from VanDykes hardware.  They have been on back order for a while now and I'm tired of waiting so now on to working on the innards.

 

I remarked before about how it was tough to keep square during the glue up.  I failed again.  The case ended up out of square.  I used tongue and groove carsiding for the back.  I cut each board wide enough to ensure coverage across the back of the out of square carcase.  Once in place I glued the tongues and nailed in the boards.  I planed the end grain by hand until both long sides were flush.

The innards for this box are pretty simple.  However, I held off on doing the tool racks until I gave it more thought.  I have opted for two rows of rack.  The first rack is for flat tools and the second for anything else.  I'm pretty sure I will lose floor space in the top compartment by making this decision, but so far I'm OK with that.

Tonight I started the top rack (flat tool).  The rack is in three layers.  The back board is 1/2" thick.  The middle layer is 1/4" thick spacer chips 1 1/8" wide.  The top layer is a 1/4" thick solid board.

I made the chips easy enough on the table saw over the weekend.  Unfortunately, I found out tonight that 1 1/8" is too wide for the spacing I want.  It is far too cold to go back out to the Outside Shop where the power tools live, so I'm stuck with the inside shop resources to make shorter spacers.  I used to have a nice bench hook made of scraps.  It got pretty chewed up, so I threw it away.  I told myself I'd make another from the scrap bin soon enough; as you might have guessed already, I never made the new bench hook.  So, here I am looking for a way to cut some small spacers in half.  I figure a bench hook is a lot cleaner than a chisel, allowing me to use both sides of the cut spacer.

Instead of making the top tool rack in less time than Pink Floyd's Dark Side Of The Moon, I cobbled together a bench hook with what I could find around the house.

Making sure the top hook is square pictures one and two.

It ain't pretty, but here is the spur of the moment bench hook for cutting little spacers smaller:

Are You Finding Keepsake Mementos This Holiday Season?

From the AYFKM holiday shopping department comes the Lee Valley digital marking gauge.  My style of working with wood does not lend itself to using a digital marking gauge.  However, if I've learned anything in life it is that there is more than one way to do anything.  Please post any practical uses for this device below.

Garrett Wade also has a fine unique offering with their ruler knife.  I'm sure this CSI inspired instrument will provide hours of entertainment.

Feel free to post links to unique or odd gifts below.

Out of Chaos Comes a Toolbox

Here is tool chaos:

I started work on a Dutch tool chest, a la Popular woodworking and Chris Schwarz.  This is another copyrighted work so I won't be posting any plan details.  However, I do have another pictorial cornucopia to offer.  OK, so maybe 'cornucopia' is too strong a word.

I'm actually going to build two of these chests.  I bought enough wood for both, but I got two lemon boards (bad humor unintended).  I cut pieces for both chests to rough length and left them to adjust for a few days.  When I got back to the pile, all the parts cut from two of the boards were egregiously warped.  I now have enough parts for one chest and a lot of firewood.

Here are the promised pics:

Glue up (duh).  Heck to keep square

Notches for lock boards

Completed notches

Ready for a skin